User Tools

Site Tools


analyzer:manual:start

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
analyzer:manual:start [2010/04/27 20:04] seststanalyzer:manual:start [2018/11/03 02:59] (current) – external edit 127.0.0.1
Line 1: Line 1:
-====== Protocol Analyzer Manual ======+{{:analyzer:manual:radar48.png |}} ===== ProtocolAnalyzer Manual ===== 
 +\\ 
 +====== Introduction ======
 The protocol Analyzer Tool is intended to help analyzing and decoding slow pulse based protocols such as IR-remote protocols and RF lamp switch protocols. The Analyzer has protocol decoders for a number of standard protocols and can decode the parameters from them. It can also help analyzing the signals of unknown protocols and help in building decoders for new protocols.  The protocol Analyzer Tool is intended to help analyzing and decoding slow pulse based protocols such as IR-remote protocols and RF lamp switch protocols. The Analyzer has protocol decoders for a number of standard protocols and can decode the parameters from them. It can also help analyzing the signals of unknown protocols and help in building decoders for new protocols. 
  
-===== Main Window ===== +Currently there are two ways of interfacing the analyzer:
-Below is the main window of the Protocol Analyzer:+
  
-{{ :analyzer:manual:main_window.png | Analyzer main window}}+  * Audio Input 
 +  * the CUL-USB Stick
  
-|1|Tool Bar | +The manual consists of the following sections:
-|2|Received signal list. Received samples and decoded messages are presented here. The **Time column** is the time the message was received. **Protocol column** specifies the name of the protocol of the received message. **Command and Address columns** refer to the protocol content. **Repeat column** specifies if the number of times the message has been repeated| +
-|3|A decoded protocol message of the JVC-protocol. Note that the JVC decoder must be active to receive this protocol. Double click this line to see details of the received message.| +
-|4|A raw sample. This actually refers to the same message as above, but is the undecoded signal. Note that the Raw-decoder must be active and view->Raw must be active to view this. Double click on these line to see the actual signal| +
-|5|Source indicator. A microphone when Audio is chosen and a USB-stick when CUL is selected| +
-|6|Scanning status. //Scanning// or //Paused//. Scanning may be paused with the //Stop Scanning//-button or because of problems opening the scanning device| +
-|7|Signal level. This is only valid for audio scanning. The bar should reach the green part on the left of the scale when a signal is received| +
- +
-===== Tool Bar ===== +
- +
-{{ :analyzer:manual:toolbar.png | Tool Bar}} +
- +
-|1|Load a session of sampled signals| +
-|2|Save the current session of sampled signals| +
-|3|Save the current session of sampled signals under a new name| +
-|4|Remove the selected row/signal| +
-|5|Remove all rows/signals in the current session| +
-|6|Edit the export template| +
-|7|Export the current decoded signals according to the specified template| +
-|8|Open the settings window| +
-|9|Start scanning| +
-|10|Stop scanning| +
-|11|Force sampling of current signal. Only valid for audio source| +
- +
-===== Decoders Window ===== +
-The Decoders Management Window is opened from the menu //view->decoders//: +
-{{ :analyzer:manual:decoders.png |Decoders Window}} +
-Here you specify which decoders should be active when receiving signals. Multiple (or all) decoders may be active simultaneously. Note that in order to see the raw (undecoded) samples, both the raw-decoder must be active and the menu item //view->Raw// must be active.+
  
 +  * [[analyzer:manual:main_window|Main Window]]
 +  * [[analyzer:manual:settings|Settings]]
 +  * [[analyzer:manual:decoders|Decoders]]
 +  * [[analyzer:manual:undecoded_window|Signal Analysis]]
 +  * [[analyzer:manual:export|Export Data]]
 +  * [[analyzer:hardware|Hardware Interface]]
 +\\
  
 +----
 +[[analyzer:manual:main_window|{{ :analyzer:manual:arrow_right_blue.png|Next - Main Window}}]]
analyzer/manual/start.1272391460.txt.gz · Last modified: 2018/11/03 02:57 (external edit)