Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
cultransceiver [2010/07/26 20:01]
sestst
cultransceiver [2018/11/03 02:59] (current)
Line 1: Line 1:
-{{:hardware64.png |}} +{{:server:hw64.png?nolink|}}
 ====== CULTransceiver ====== ====== CULTransceiver ======
-This module is a part of the [[NetHomeServer]]. The CULTransceiver is an interface module for the CUL USB radio transceiver. The CUL transceiver is sold by [[http://​busware.de/​tiki-index.php?​page=CUL | BusWare]]. The NetHomeServer project has custom firmware designed for CUL which works with the CULTransceiver. ​+This module is a part of the [[start|NetHomeServer]]. The CULTransceiver is an interface module for the [[cul|CUL USB radio transceiver]]. The CUL transceiver is sold by [[http://​busware.de/​tiki-index.php?​page=CUL | BusWare]]. The NetHomeServer project has custom firmware designed for CUL which works with the CULTransceiver
 + 
 +To use the CULTransceiver USB-drivers has to be installed for the Windows operation system. Instructions for this is located [[installculusb|here]]. 
 + 
 +You also have to install the NetHome firmware on the CUL-device and this is described [[installculfirmware|here]].
  
 ===== Attributes ===== ===== Attributes =====
   * **SerialPort** //[get] [set]// The hardware presents itself to the OS as a serial port, the name of the serial port is configured here.   * **SerialPort** //[get] [set]// The hardware presents itself to the OS as a serial port, the name of the serial port is configured here.
   * **ModulationFrequency** //[get] [set]// The NetHome CUL firmware can modulate the radio signal with a frquency. This is primarally used when communicating with devices which sends the signal as IR. If set to 0, the modulation is disabled by default and only enabled by any underlying protocol which can specify modulation (like the Pronto protocol)   * **ModulationFrequency** //[get] [set]// The NetHome CUL firmware can modulate the radio signal with a frquency. This is primarally used when communicating with devices which sends the signal as IR. If set to 0, the modulation is disabled by default and only enabled by any underlying protocol which can specify modulation (like the Pronto protocol)
-  * **TransmissionPower** //[get] [set]// The output power level. There are five power levels +  * **TransmissionPower** //[get] [set]// The output power level. There are deven power levels available: 0 = -30 dBm, 1 = -20 dBm, 2 = -15 dBm, 3 = -10 dBm, 4 = 0 dBm, 5 = 5 dBm, 6 = 7 dBm, 7 = 10 dBm
-available: ​ 0 = -30 dBm, 1 = -20 dBm, 2 = -15 dBm, 3 = -10 dBm, 4 = 0 dBm, 5 = 5 dBm, 6 = 7 dBm, 7 = 10 dBm+
   * **SendCount** //[get]// Number of messages sent   * **SendCount** //[get]// Number of messages sent
   * **Connected** //[get]// Connection state ("​Connected"​ or "Not Connected"​)   * **Connected** //[get]// Connection state ("​Connected"​ or "Not Connected"​)
   * **TestBeepFrequency** //[get] [set]// Frequency of short test beep   * **TestBeepFrequency** //[get] [set]// Frequency of short test beep
 +
 ===== Actions ===== ===== Actions =====
   * **Reconnect** ​ Attempt to reconnect with the hardware   * **Reconnect** ​ Attempt to reconnect with the hardware

Personal Tools